Only use a weed and feed if the weed infestation is completely uniform over the entire lawn and all species of weeds targeted will be affected by the herbicide in the weed and feed. This scenario doesn’t occur often, so it is more likely the use of an herbicide and a fertilizer separately will be needed. If the weeds are uniformly spread over the area to be treated, match the appropriate weed and feed product to your grass, the seed you have recently applied or want to apply, and the time of year.
It is important to know what kind of grass you have growing or want to have growing. Certain chemicals act differently on different species of grass and weeds. For example, the common herbicide 2,4-D is toxic to some cultivars of St. Augustine grass (Stenotaphrum secundatum), which grows in the area roughly covered by U.S. Department of Agriculture plant hardiness zones 8 through 10. Another common herbicide, atrazine, is potentially lethal to grass when applied in temperatures above 85 degrees Fahrenheit. Use the instructions on the bag of each weed and feed product to determine how it will affect seeding.
It’s important to know a little about herbicides so you can make the best choice for when to apply seed in an area that has been treated for weeds. The most common types of herbicide in weed and feed products are selective and systemic. Selective herbicides target a species of plant to kill while systemic herbicides work by being absorbed though the roots and then transported throughout the plant, killing it from within. Read the bag label to see what kind of herbicide is used in the weed and feed you are considering using or have used. The bag label will tell you how many days you must wait before applying seed to a lawn that has been treated with that product.
Herbicides can target weeds before they germinate from seed – pre-emergent – or as developed plants – post-emergent. Before you seed, you can use a non-selective, post-emergent herbicide to control any weeds in the area to be seeded. Most of these can be applied up to two weeks before seeding to control any existing weeds. Herbicides should not be used after seeding until the new seedlings are established. Mowing and spot treatments can be used to control weeds until the seeded area is actively growing and requires only maintenance watering. Establishment times vary depending on the type of seed you use and your weather conditions.
Weed and feed fertilizers are often used in combination with seeding. Weed and feed formulations consist of two components: a herbicide to kill weeds and a fertilizer to strengthen the turf. The herbicide will weaken the grass as well as the weeds and the fertilizer will strengthen the weeds as well as the grass. When applying seed over a weed and feed application, remember that some weed and feeds can prevent grass seeds from growing.
Using Weed and Feed
Sara DeBerry is a graduate of the University of Florida holding a masters degree in environmental horticulture and a minor in entomology and nematology. DeBerry has been writing for government agencies since 2004 and has published peer reviewed scientific articles during her studies at UF.
Each year during the fall overseeding season, we get a lot of folks that come in to the Grass Pad and say, “I followed your fall lawn renovation program; I used your weed-free grass seed. Why do I have weeds in my yard?” Our response is “Well, it means you really did it right!”
Where Did All These Weeds Come From?
Dandelion, clover, spurge, and numerous other broadleaf weeds are stimulated as well. If you should have just a few weeds here and there, pull them by hand. However, if you are overrun, fall is an excellent time to control those broadleaf weeds. Perennial broadleaf weeds are busy sucking up much-needed nutrients to store for overwintering. An application of Gordon’s Trimec or Speedzone can be applied 28 days after grass seed germination. A fall application of Gordon’s Trimec with Uncle’s Stikit, spreader sticker or a granular application of Loveland Weed and Feed will be quickly absorbed by the broadleaf weeds and is sure to kill to the roots.
Controlling Broadleaf Weeds after Seeding
Disturbing the soil (verticutting, aerating, dethatching or raking) exposes soil and any pre-existing weed seeds that lay dormant in the soil. These weed seeds could be from last year or several years ago, suspended under the soil, too deep to germinate waiting for their opportunity to spring into life.